Источник бесперебойного питания TRIPP LITE SMX500RT1U. Инструкция на русском языке

Owner’s Manual
SmartPro  1U Rackmount
®
Intelligent, Line-Interactive UPS System
SMX500RT1U
Series: AG-0098
Important Safety Instructions                    2
Mounting                                         3
Quick Installation                               4
Optional Installation                            6
Basic Operation                                  7
Storage and Service                             10
Battery Replacement                             10
Product Registration                            11
Espanol                                         12
Francais                                        23
Ponneee                                         34
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an
ISOBAR6ULTRA surge protector—
a $50 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright ©2015 Tripp Lite. All rights reserved. SmartPro  is a registered trademark of Tripp Lite.
®
1
15-01-102-9332C7.indb   1                                       1/16/2015   10:38:44 AM

Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be followed during the installation, operation
and storage of all Tripp Lite UPS Systems. Failure to heed these warnings will void your warranty.
UPS Location Warnings
•  Use caution when lifting your UPS. Because of the considerable weight of all rackmount UPS
systems, at least two people should assist in lifting and installing them.
•  Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.
•  For best performance, the ambient temperature near your UPS should be between 0° C and
40° C (between 32° F and 104° F).
•  Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its
vents or fan openings.
UPS Connection Warnings
•  The UPS contains its own energy source (battery). The output terminals may be live even
when the UPS is not connected to an AC supply.
•  Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS’s plug in a
way that would eliminate the UPS’s connection to ground. Do not use adapters that eliminate
the UPS’s connection to ground.
•  Do not plug your UPS into itself; this will damage the UPS and void your warranty.
•  If you are connecting your UPS to a motor-powered AC generator, the generator must provide
filtered, frequency-regulated, computer-grade output.
Equipment Connection Warnings
•  Do not use Tripp Lite UPS Systems for life support applications in which a malfunction or
failure of a Tripp Lite UPS System could cause failure or significantly alter the performance
of a life-support device.
•  Do not connect surge suppressors or extension cords to the output of your UPS. This might
overload the UPS and will void the surge suppressor and UPS warranties.
Battery Warnings
•  Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe
proper precautions. Do not dispose of the batteries in a fire. Do not open the UPS or batteries.
Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before
performing battery replacement. Use tools with insulated handles. There are no user-serviceable
parts inside the UPS. Battery replacement should be performed only by authorized service
personnel using the same number and type of batteries (sealed Lead-Acid). The batteries are
recyclable. Refer to your local codes for disposal requirements or in the USA only call
1-800-SAV-LEAD or 1-800-8-BATTERY (1-800-8-228-8379) or visit www.call2recycle.org for
recycling information. Tripp Lite offers a complete line of UPS System Replacement Battery
Cartridges (R.B.C.). Visit Tripp Lite on the Web at www.tripplite.com to locate the specific
replacement battery for your UPS.
•  During hot-swap battery replacement, the UPS will not provide backup power in the event of
a blackout or other power interruptions.
•  Do not operate UPS without batteries.
•  When adding external battery packs to select models with external battery pack connectors,
connect only Tripp Lite-recommended battery packs of the correct voltage and type. Do not
connect or disconnect battery packs when the UPS is operating on battery power.
2
15-01-102-9332C7.indb   2                                       1/16/2015   10:38:44 AM

Mounting
Mount your equipment in either a 4-post or 2-post rack or rack enclosure. The user must
determine the fitness of hardware and procedures before mounting. If hardware and procedures
are not suitable for your application, contact the manufacturer of your rack or rack enclosure. The
procedures described in this manual are for common rack and rack enclosure types and may not
be appropriate for all applications.
4-Post Rack Mounting
All UPS models include hardware required to mount in a 4-post rack.
1   Attach mounting ears   to the front
A
mounting holes of your equipment   using
B
C
the screws provided  . The ears should                     C
face forward.
B
A
1
2   Using an assistant if necessary, lift your
equipment and mount it to the rack. Attach
it by screwing the appropriate hardware
D
through its mounting ears and into the rack   D
rails.
2        D
2-Post (Telecom) Rack Mounting
Following the procedures below, mount the 1U UPS model in 2-post racks with the included
hardware.
1    Attach mounting ears   to the front
A
mounting holes of your UPS   using the
B
screws provided   . The ears should face                  C
C
backward.
B
A
1
2   Using an assistant if necessary, lift your UPS
and attach it to the rack by passing the
screws, nuts and washers provided
D
through its mounting ears and into the rack
rails.
D
2       D
3
15-01-102-9332C7.indb   3                                       1/16/2015   10:38:47 AM