Источник бесперебойного питания TRIPP LITE SMARTINT3000VS. Инструкция на русском языке

200404080 932245 SMARTINT22003000VS OM.qxd  5/26/2004  4:26 PM  Page 1
Owner’s Manual
Models: SMARTINT2200VS & SMARTINT3000VS
Intelligent, Line-Interactive UPS Systems (Tower Configuration)
• 230V Input • 2200VA - 3000VA Capacities • Extended-Run Options*
* SMARTINT3000VS model
Important Safety Instructions                                 2
Quick Installation                                            3
Optional Installation                                         4
Basic Operation                                               5
Storage & Service                                             10
Specifications                                                10
Espanol                                                       11
Francais                                                      22
Ponneee                                                       33
1111 W. 35th Street  Chicago, IL 60609 USA
Customer Support: (773) 869-1234  • www.tripplite.com
Copyright © 2004 Tripp Lite. All rights reserved. SmartPro ® is a registered trademark of Tripp Lite.

200404080 932245 SMARTINT22003000VS OM.qxd  5/26/2004  4:26 PM  Page 2
Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be followed during the installation,
operation and storage of all Tripp Lite UPS Systems.
UPS Location Warnings
• Install your UPS indoors, away from excess moisture or heat, conductive contaminants,
dust or direct sunlight.
• For best performance, keep the indoor temperature between 32? F and 104? F
(0? C and 40? C).
• Leave adequate space around all sides of the UPS for proper ventilation.
• Do not install the UPS near magnetic storage media, as this may result in data corruption.
UPS Connection Warnings
• Connect your UPS directly to a properly grounded AC power outlet. Do not plug the UPS
into itself; this will damage the UPS.
• Do not modify the UPS’s plug, and do not use an adapter that would eliminate the UPS’s
ground connection.
• Do not use extension cords to connect the UPS to an AC outlet. Your warranty will be
voided if anything is used to connect your UPS to an outlet.
• If the UPS receives power from a motor-powered AC generator, the generator must
provide clean, filtered, computer-grade output.
Equipment Connection Warnings
• Do not use Tripp Lite UPS Systems for life support applications in which a malfunction
or failure of a Tripp Lite UPS System could cause failure or significantly alter the
performance of a life-support device.
• Do not connect surge suppressors or extension cords to the output of your UPS.
Battery Warnings
• Batteries can present a risk of electrical shock and burn from high short-circuit current.
Observe proper precautions. Do not dispose of the batteries in a fire. Do not open the
UPS or batteries. Do not short or bridge the battery terminals with any object. Unplug
and turn off the UPS before performing battery replacement. Use tools with insulated
handles. There are no user-serviceable parts inside the UPS. Battery replacement should
be performed only by authorized service personnel using the same number and type of
batteries (sealed Lead-Acid). The batteries are recyclable. Refer to your local codes for
disposal requirements or in the USA only call 1-800-SAV-LEAD or 1-800-8-BATTERY
(1-800-8-228-8379) or visit www.rbrc.com for recycling information. Tripp Lite offers a
complete line of UPS System Replacement Battery Cartridges (R.B.C.). Visit Tripp Lite
on the Web at www.tripplite.com to locate the specific replacement battery for your UPS.
• If your UPS model is equipped with an external battery connector, only connect Tripp Lite
battery packs of the appropriate type and correct voltage. Do not connect or disconnect
external batteries while the UPS is operating from battery.
2

200404080 932245 SMARTINT22003000VS OM.qxd  5/26/2004  4:26 PM  Page 3
Quick Installation
1  Insert a user-supplied power
cord (with country-specific plug)
into the UPS System’s IEC-320-C20
AC Input Receptacle. Plug the
cord into an AC wall outlet.
NOTE! After you plug the UPS into a live AC outlet, the UPS (in
“Standby” mode) will automatically charge its batteries, but will  1
not supply power to its outlets until it is turned ON.
Shown: SMARTINT2200VS
2  Using the jumper cords supplied
with the UPS, plug your equipment
into the UPS.*
* Order additional jumper cords from Tripp Lite. Call (773) 869-1234;
order part # P004-006. Your UPS is designed to support only com-
puter equipment. You will overload the UPS if the total VA ratings for
all the equipment you connect exceeds the UPS's Output Capacity
(see Specifications). To find your equipment's VA ratings, look on
their nameplates. If the equipment is listed in amps, multiply the  2
number of amps by 230 to determine VA. (Example: 1 amp ? 230 =
230 VA). If you are unsure if you have overloaded the UPS’s outlets, see
“OUTPUT LOAD LEVEL” LED description.
3  Turn the UPS ON.
Press and hold the “ON/OFF/STANDBY” button for
one second. The alarm will beep once after one second
has passed. Release the button.
3
3