Блок распределения питания (PDUs) TRIPP LITE PDUMV32HVNET. Инструкция на русском языке

Warranty
Register online today for a
Registration
chance to win a FREE Tripp Lite   Owner’s Manual
product! www.tripplite.com/warranty
Switched Rack PDU
Zero U (Vertical) Format
Important Safety Instructions                                  2
Installation                                                   2
Features                                                       6
Configuration and Operation                                    8
Technical Support                                              8
Warranty and Warranty Registration                             9
Espanol                                                       10
Francais                                                      19
1111 W. 35th Street • Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2009 Tripp Lite. All rights reserved.
1
200912032  93-2721.indd   1                                    12/17/2009   11:03:08 AM

Important Safety Instructions
SAVE THESE INSTRUCTIONS
This  manual  contains  instructions  and  warnings  that  should  be
followed during the installation, operation, and storage of this product.
Failure to heed these instructions and warnings will void the product
warranty.
•  The PDU provides convenient multiple outlets, but it DOES NOT provide surge or line noise
protection for connected equipment.
•  The PDU is designed for indoor use only in a controlled environment away from excess moisture,
temperature extremes, conductive contaminants, dust or direct sunlight.
•  Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that eliminate
the connection to ground.
•  The power requirement for each piece of equipment connected to the PDU must not exceed the
individual outlet’s load rating.
•  The total power requirement for equipment connected to the PDU must not exceed the maximum
load rating for the PDU.
•  Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable
parts inside.
•  Do not attempt to modify the PDU, including the input plugs and power cables.
•  Do not attempt to use the PDU if any part of it becomes damaged.
•  Do not attempt to mount the PDU to an insecure or unstable surface.
•  Never attempt to install electrical equipment during a thunderstorm.
•  Use of this equipment in life support applications where failure of this equipment can reasonably
be expected to cause the failure of the life support equipment or to significantly affect its safety or
effectiveness is not recommended. Do not use this equipment in the presence of a flammable
anesthetic mixture with air, oxygen or nitrous oxide.
Installation
Mounting the PDU
Note: The illustrations may differ somewhat from your PDU model. Regardless of configuration, the user must determine the fitness of
hardware and procedures before mounting. The PDU and included hardware are designed for common rack and rack enclosure types
and may not be appropriate for all applications. Exact mounting configurations may vary. Screws for attaching the mounting brackets
and cord retention shelf to the PDU are included. Use only the screws supplied by the manufacturer, or their exact equivalent (#6-32,
?" flat head).
1-1 Attach the mounting brackets to the PDU.
1-2 (Optional) Attach the cord retention
bracket(s) to the PDU.
1-3 Attach the PDU to a vertical rail in your
rack or rack enclosure. (Use the mounting
hardware that came with your rack or rack
enclosure to attach the mounting brackets to
the rail.)
1-1         1-2         1-3
2
200912032  93-2721.indd   2                                    12/17/2009   11:03:10 AM

Installation continued
Connecting the PDU
2-1 (Models with IEC power inlet or 3-pole
IEC 309 plug only.) Select models have a     C
detachable power cord. Attach the included
power cord to the PDU by inserting the IEC   A
connector  A  of the power cord into the IEC
power inlet  B  located near the end of the PDU.
Use the included bracket  C  to secure the power
cord connection.
Note: Optionally, a user-supplied power cord can be attached
to the PDU by connecting it to the IEC inlet. Do not attempt to   2-1  B
attach a user-supplied power cord unless it is certified to be
compatible with the input power source that will be used by the
PDU.                                                          A
B
2-2 (Optional - models with input plug adapter
only.) Select models include an input plug
adapter that converts the twist-lock input plug
to a straight-blade input plug. Attach the input
plug adapter  A   to the input plug  B  if you wish
to plug the PDU into a compatible straight-
blade outlet.                      2-2
2-3 Connect the input plug to a compatible AC
power outlet. If the PDU does not have a circuit
breaker, it should be provided with a branch-
rated over-current protection device that
matches the rated amperage of the PDU.
Note: The AC power source should not share a circuit with a
heavy electrical load.
2-3
2-4 Connect your equipment's input plugs  A
to the outlets  B  of the PDU. The LED  C   near
each outlet illuminates when the outlet is ready   B
to distribute live AC power. The digital load
meter  D  displays the total connected equipment
load in amps. (Select models provide additional   C         A
load data. See the Features section for more
information.)
Note: In order to minimize interference among connected
devices, connect each device to the nearest PDU outlet and coil
excess power cord length.                                  D
2-4
2-5 (Optional) If you attached the cord
retention bracket(s), tie each equipment power
cord to the retention bracket. Attach each cord
to the retention shelf by looping the cord and
securing it with one of the included cable ties              A
A . Make sure that each cord can be unplugged
from the PDU without removing the cable tie.
2-5
3
200912032  93-2721.indd   3                                    12/17/2009   11:03:11 AM