Блок распределения питания (PDUs) TRIPP LITE PDUMV16HV. Инструкция на русском языке

Owner’s Manual
Metered Rack PDU
Model: PDUMV16HV
(Series Number: AGPD6674)
Espanol: p6 • Francais: p11 • Русский: p16
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2014 Tripp Lite. All rights reserved.
1
14-04-098-933312.indb   1                                       4/24/2014   10:23:23 AM

Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be
followed during the installation, operation and storage of this
product. Failure to heed these instructions and warnings will void
the product warranty.
Important Warnings
• The PDU provides convenient multiple outlets but it DOES NOT provide surge or line
noise protection for connected equipment.
• The PDU is designed for indoor use only in a controlled environment away from excess
moisture, temperature extremes, conductive contaminants, dust or direct sunlight.
• Use of this equipment in life support applications where failure of this equipment
can reasonably be expected to cause the failure of the life support equipment or to
significantly affect its safety or effectiveness is not recommended. Do not use this
equipment in the presence of a flammable anesthetic mixture with air, oxygen or
nitrous oxide.
• Do not connect the PDU to an ungrounded outlet or extension cords or adapters that
eliminate the connection to ground.
• The power requirement for each piece of equipment connected to the PDU must not
exceed the individual outlet’s load rating.
• The total power requirement for equipment connected to the PDU must not exceed the
maximum load rating for the PDU.
• Do not drill into or attempt to open any part of the PDU housing. There are no user-
serviceable parts inside.
• Do not attempt to modify the PDU, including the input plugs and power cables.
• Do not attempt to use the PDU if any part of it becomes damaged.
• Do not attempt to mount the PDU to an insecure or unstable surface.
• Never attempt to install electrical equipment during a thunderstorm.
•  The PDU must be installed by a qualified technician only.
•  Install in accordance with National Electrical Codes. Be sure to use the proper over
current protection for the installation, in accordance with the plug rating/equipment
rating.
•  The electrical sockets supplying power to the equipment shall be installed near the
equipment and be easily accessible.
2
14-04-098-933312.indb   2                                       4/24/2014   10:23:23 AM

Installation
Note: The user must determine the fitness of hardware and procedures before mounting. The PDU and included
hardware are designed for common rack and rack enclosure types and may not be appropriate for all applications.
1A 0U Rack Configuration (Mounting
Brackets). Prior to installation,
determine the rack location in which
the PDU is to be installed. Attach
the mounting brackets to the back
of the PDU as shown, using the
included screws. To assist with proper
positioning, the brackets have four
screw holes each; make sure that
the same two holes are used to
attach each bracket to the PDU.
After attaching the brackets, position
the PDU in the rack and mount it by
installing four user-supplied screws
through the brackets into the rack.  1A
1B 0U Rack Configuration (Mounting
Buttons). Attach the included
mounting buttons to the PDU.
Position the PDU as desired in the
rack enclosure, align the buttons with
the rack mounting slots, and slide the
PDU into position.              1B
1C Under-Counter Configuration. The
PDU may be installed under a counter
using the included mounting brackets.
Attach the mounting brackets to the
back of the PDU as shown in STEP
1A. Secure the PDU to the underside
of the counter by installing two user-
supplied screws through each bracket
into the counter.
1C
3
14-04-098-933312.indb   3                                       4/24/2014   10:23:25 AM