Блок распределения питания (PDUs) TRIPP LITE PDUMH20HVNET. Инструкция на русском языке

Register online today for a chance   Owner’s Manual
Warranty
to win a FREE Tripp Lite product!
Registration
www.tripplite.com/warranty
PDUMH15NET/PDUMH20NET
Switched Rack PDU
• 120V, 60Hz AC Input and Output
PDUMH15HVNET/PDUMH20HVNET
Switched Rack PDU
• 208/230V, 50/60Hz AC Input and Output
Important Safety Instructions                                  2
Installation                                                   2
Features                                                       9
Configuration and Operation                                   11
Technical Support                                             12
Warranty and Warranty Registration                            12
Espanol                                                       13
Francais                                                      25
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2011 Tripp Lite. All rights reserved.
1
201110149-93-2718.indd   1                                      11/9/2011   11:17:25 AM

Important Safety Instructions
SAVE THESE INSTRUCTIONS
This  manual  contains  instructions  and  warnings  that  should  be
followed during the installation, operation, and storage of this product.
Failure to heed these instructions and warnings may affect the product
warranty.
•  The PDU provides convenient multiple outlets, but it DOES NOT provide surge or line noise
protection for connected equipment.
•  The PDU is designed for indoor use only in a controlled environment away from excess moisture,
temperature extremes, conductive contaminants, dust or direct sunlight.
•  Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that eliminate
the connection to ground.
•  The power requirement for each piece of equipment connected to the PDU must not exceed the
individual outlet’s load rating.
•  The total power requirement for equipment connected to the PDU must not exceed the maximum
load rating for the PDU.
•  Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable
parts inside.
•  Do not attempt to modify the PDU, including the input plugs and power cables.
•  Do not attempt to use the PDU if any part of it becomes damaged.
•  Do not attempt to mount the PDU to an insecure or unstable surface.
•  Never attempt to install electrical equipment during a thunderstorm.
•  Use of this equipment in life support applications where failure of this equipment can reasonably
be expected to cause the failure of the life support equipment or to significantly affect its safety or
effectiveness is not recommended. Do not use this equipment in the presence of a flammable
anesthetic mixture with air, oxygen or nitrous oxide.
Installation
Mounting the PDU
The PDU supports five primary mounting configurations: 1U Rack, 0U Rack (Vertical), Wall, Under-
Counter and Reduced-Depth.
Note: Regardless of  configuration, the user must determine the fitness of hardware and procedures before mounting. The PDU and
included hardware are designed for common rack and rack enclosure types and may not be appropriate for all applications. Exact
mounting configurations may vary. Screws for attaching the mounting brackets and cord retention shelf to the PDU are included. Use
only the screws supplied by the manufacturer, or their exact equivalent (#6-32, 3/16" flat head).
1-1 1U Rack Mounting: Use 3 screws  A  to                 A
attach each of the 2 longer mounting brackets  B    A
to the PDU as shown. You can mount the PDU in
a recessed position by attaching the mounting
brackets so they extend beyond the front panel of      B
the PDU. (If you plan to use the cord retention
shelf, attach the mounting brackets in a recessed
position.) Mount the PDU in the rack by
inserting 4 user-supplied screws  C  through the
mounting brackets  D  and into the mounting
holes of the rack rails.                            D
C
1-1
2
201110149-93-2718.indd   2                                      11/9/2011   11:17:26 AM

Installation continued
1-2 0U Rack Mounting: Use 3 screws  A  to
attach each of the 2 shorter mounting brackets
B  to the PDU as shown. Mount the PDU
vertically by inserting 2 or more user-supplied   B
screws  C  through the mounting brackets  D   and     D        C
into mounting points in the rack or rack
enclosure.
1-3 Wall Mounting: Use 3 screws  A  to attach   A
each of the 2 shorter mounting brackets  B  to the   1-2
PDU as shown. Mount the PDU to the wall by
inserting 2 or more user-supplied screws  C
through the mounting brackets  D  and into
secure mounting points.
1-4 Under-Counter Mounting: Use 3 screws    B
A  to attach each of the 2 shorter mounting           D        C
brackets  B  to the PDU as shown. Mount the
PDU under the counter by inserting 2 or more
user-supplied screws  C  through the mounting   A
brackets  D  and into secure mounting points.
1-5 Reduced-Depth Mounting: Use 3 screws   1-3
A  to attach each of the 2 shorter mounting
brackets  B  to the PDU as shown. Mount the        B
PDU to a stable surface with the outlets facing   A
upward by inserting 2 or more user-supplied
screws  C  through the mounting brackets  D  and
into secure mounting points.
D
1-6 Cord Retention Shelf Attachment
(Optional): Use 2 screws  A  to attach the cord
retention shelf  B  to the front panel of the PDU.
C
1-4
D
B
C
A
1-5
B
A
1-6
3
201110149-93-2718.indd   3                                      11/9/2011   11:17:28 AM