Блок распределения питания (PDUs) TRIPP LITE PDU3XMV6G20. Инструкция на русском языке

Owner’s Manual
3-Phase Metered
Power Distribution Units
PDU3MV6L2120           PDU3MV6L2130            PDU3XMV6G20
(Series Number: AGPD8414)  (Series Number: AGPD8415)  (Series Number: AGPD8420)
PDU3MV6L2120LV           PDU3MV6H50            PDU3XMV6L2220
(Series Number: AGPD8414)  (Series Number: AGPD8416)  (Series Number: AGPD8420)
PDU3MV6L2120B            PDU3MV6H50A           PDU3MV6L2130A
(Series Number: AGPD8414)  (Series Number: AGPD8417)  (Series Number: AG-00E3)
Important Safety Insructions                   2
Installation                                   3
Digital Load Meter                             6
Features                                       7
Service                                        8
Warranty and Product Registration              9
Espanol                                      10
Francais                                     19
???????                                      28
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2015 Tripp Lite. All rights reserved.
1
15-07-049-933145.indb   1                                        8/7/2015   1:58:11 PM

Important Safety Instructions
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that should be followed during
the installation, operation, and storage of this product. Failure to heed these
instructions and warnings may affect the product warranty.
•  The PDU provides convenient multiple outlets, but it DOES NOT provide surge or line noise
protection for connected equipment.
•  The PDU is designed for indoor use only in a controlled environment away from excess
moisture, temperature extremes, conductive contaminants, dust or direct sunlight.
•  Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that
eliminate the connection to ground.
•  The power requirement for each piece of equipment connected to the PDU must not exceed
the individual outlet’s load rating.
•  The total power requirement for equipment connected to the PDU must not exceed the
maximum load rating for the PDU.
•  Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable
parts inside.
•  Do not attempt to modify the PDU, including the input plugs and power cables.
•  Do not attempt to use the PDU if any part of it becomes damaged.
•  Do not attempt to mount the PDU to an insecure or unstable surface.
•  Use of this equipment in life support applications where failure of this equipment can
reasonably be expected to cause the failure of the life support equipment or to significantly
affect its safety or effectiveness is not recommended. Do not use this equipment in the
presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.
•  Never attempt to install electrical equipment during a thunderstorm.
•  Keep indoor ambient temperature between 32°F and 104°F (0°C and 40°C).
•  Connect the PDU to an outlet that is in accordance with your local building codes and that is
adequately protected against excess currents, short circuits and earth faults.
•  Do not attempt to open the PDU; there are no user-serviceable parts inside.
•  The PDU must be installed by a qualified technician only.
•  Install in accordance with National Electrical Codes. Be sure to use the proper over current
protection for the installation, in accordance with the plug rating/equipment rating.
•  The electrical sockets supplying power to the equipment shall be installed near the equipment
and be easily accessible.
2
15-07-049-933145.indb   2                                        8/7/2015   1:58:11 PM

Installation
Mounting the PDU
Note: The illustrations may differ somewhat from your PDU model. Regardless of configuration, the user must
determine the fitness of hardware and procedures before mounting. The PDU and included hardware are
designed for common rack and rack enclosure types and may not be appropriate for all applications. Exact
mounting configurations may vary. Screws for attaching the mounting brackets and cord retention shelf to the
PDU are included. Use only the screws supplied by Tripp Lite, or their exact equivalent.
1-1    Attach the mounting   1-2    (Optional) Attach the   1-3    For toolless mounting,
brackets to the PDU.   cord retention         position the PDU as
bracket(s) to the PDU.  desired in the rack
enclosure, align the
buttons with the rack
mounting slots, and
slide the PDU into
position.
1-1                    1-2                    1-3
1-4    To install the PDU with its outlets facing   B
the rear of the rack, use the included      A
PDUMVROTATEBRKT accessory. First,
attach the mounting button  A  to the
V-shaped bracket  B  using the included
screw and washer. Then, use the
button-mount slot to attach the bracket
to the PDU and the mounting button to
attach the PDU to the rack. The bracket
effectively repositions the mounting
brackets, allowing for the PDU outlets to
face the rear of the rack.
1-4
1-5    If your PDU cannot be mounted
using the toolless mounting option,
the mounting brackets can be used.
Attach the PDU to a vertical rail in
your rack or rack enclosure. (Use the
mounting hardware that came with your
rack or rack enclosure to attach the
mounting brackets to the rail.)  1-5
3
15-07-049-933145.indb   3                                        8/7/2015   1:58:13 PM