На сайте 124169 инструкций общим размером 502.7 Гб, которые состоят из 6277380 страниц

Сетевой фильтр TRIPP LITE DNET1. Инструкция на русском языке

Руководство пользователя TRIPP LITE DNET1. Основные функции, характеристики и условия эксплуатации изложены на 12 страницах документа в pdf формате.

Информация

Раздел
Электроника
Категория
Аккумуляторы / Источники питания
Тип устройства
Сетевой фильтр
Производитель (бренд)
TRIPP LITE
Модель
TRIPP LITE DNET1
Еще инструкции
Аккумуляторы / Источники питания TRIPP LITE, Сетевые фильтры TRIPP LITE
Язык инструкции
русский
Дата создания
05 Февраля 2021 г.
Просмотры
84 просмотра
Количество страниц
12
Формат файла
pdf
Размер файла
1.42 Мб
Название файла
tripp_lite_manual_dtel2.pdf

Фото

Страница 1Страница 2Страница 3Страница 4

Просмотр

Доступно к просмотру 12 страниц. Рекомендуем вам скачать файл инструкции, поскольку онлайн просмотр документа может сильно отличаться от оригинала.

  • Owner’s Manual
    Network Dataline
    Surge Suppressors
    ™
    Data Shield  by Tripp Lite Network Dataline Surge Suppressors are designed to protect
    data and communications equipment against AC transients caused by lightning, electrostatic
    discharge and ground surges that can enter equipment from the signal lines or chassis ground.
    Data Shield by Tripp Lite Network Dataline Surge Suppressors described here protect
    networked equipment using 100Base-T, 10Base-T, 10Base-2 and Ethernet, Token Ring,
    RS232, RS422, parallel, dial-up modems, fax, ISDN, DDS, T-1 and other communication
    interfaces.
    Tripp Lite World Headquarters
    th
    1111 W. 35  Street, Chicago, IL 60609 USA
    (773) 869-1234 • www.tripplite.com
    Note: Follow these instructions to ensure proper operation and prevent damage to this device
    and its connected equipment.
    Copyright © 2008 Tripp Lite. All rights reserved. All trademarks are the property of their respective owners.
    1
    200810167  93-2858.indd   1                                     12/16/2008   9:58:50 AM
  • INSTALLATION
    1.  Make sure the computer, network device or other equipment is logged OFF the network
    (if applicable). Turn OFF power to the equipment.
    2.  Disconnect the cable from the equipment to be protected.
    3.  Connect the Data Shield by Tripp Lite Network Dataline Surge Suppressor directly to the
    equipment. DB9 and DB25 models are reversible, to work with male or female ports. To
    change gender, remove the thumbscrews, reverse their direction and re-install.
    4.  Attach the green ground wire on the surge suppressor directly to the protected
    equipment’s chassis. (Except DB9 and DB25 models.)
    5.  Reconnect the cable to the Data Shield by Tripp Lite Network Dataline Surge
    Suppressor.
    NOTE!
    The Data Shield by Tripp Lite Network Dataline Surge Suppressor must be properly grounded and positioned as close
    as possible to the equipment to be protected. For best results, it is required that the length of the signal line and ground
    wire (if equipped) between the surge suppressor and the protected equipment be kept as short as possible, not to
    exceed 12 inches (12”). It is best to install the surge suppressor directly to the equipment, as noted above.
    NOTE!
    Installing a typical Data Shield by Tripp Lite Network Dataline Surge Suppressor is equivalent to adding
    approximately three feet (3’) of typical data communication cable to a segment.
    CAUTION!
    The Data Shield by Tripp Lite Network Dataline Surge
    Suppressor does not protect the equipment on the opposite end
    of the cable. Normally, protection at both ends is recommended.
    CAUTION!
    Use of this equipment in life support applications where failure
    of this equipment can reasonably be expected to cause the
    failure of the life support equipment or to significantly affect its
    safety or effectiveness is not recommended. Do not use this
    equipment in the presence of a flammable anesthetic mixture
    with air, oxygen or nitrous oxide.
    CAUTION!
    When properly installed, the Data Shield by Tripp Lite Network
    Dataline Surge Suppressor will only protect against surges on
    the dataline portion of your installation. Simultaneous AC surge
    ®
    suppression/power protection in the form of an ISOBAR  surge
    suppressor or Tripp Lite UPS system is strongly recommended
    for complete system/network protection and can also extend
    Ultimate Lifetime Insurance coverage to connected equipment.
    2
    200810167  93-2858.indd   2                                     12/16/2008   9:58:51 AM
  • SPECIFICATIONS
    All surge suppressors listed have component response times of less than 1 picosecond.
    Nominal            Peak Pulse
    Model:         Description:            Clamping Voltage:  Current:
    DRS232         RJ45/RJ11 protector for
    100Base-T4, RS232 on twisted Pair   18 volts, protecting    1340 amps
    (wires 1-8) or ISDN “S/T” interfaces.   wires 1-8
    Supplied with a 4” RJ45 patch cable.
    RJ45 100Base-T, 10Base-T,
    DNET1          Token Ring, RS422, AS400/Sys3x   7.5 volts, protecting
    protector for NICs, hubs, routers,   wires 1-8  750 amps
    etc. Supplied with 4” RJ45 patch
    cable.
    RJ45/RJ11 protector for nonspan
    DSUT1CSU       powered T-1 equipment, digital data
    service CSUs/DSUs, ISDN “U”   60 volts, protecting    200 amps
    wires 1-8
    interfaces or other digital lines.
    Supplied with 4” RJ45 patch cable.
    DTEL2          RJ45/RJ11 for modems, answering
    and fax machines. Supplied with  260 volts, protecting center  250 amps
    4 wires (2 CO-lines)
    4” RJ11 patch cable.
    Serial DB9 RS232 protector for male
    or female ports of data terminal and
    DB9
    computing equipment including PCs,  18 volts, protecting pins
    modems, etc. (Any male or female   1-9 and chassis  340 amps
    9-pin port). Male/Female genders
    are reversible with reversible
    thumbscrews.
    Serial DB25 RS232 protector
    DB25           (wires 1-8, 20) for male or female
    ports of data terminal & computing   18 volts, protecting pins
    equipment including PCs, printers,   1-8, 20 and chassis  340 amps
    modems, etc. Male/Female genders
    are reversible with reversible
    thumbscrews.
    DB25-ALL       DB25-ALL: Serial DB25 RS232
    protector (pins 1-25) for any 25-pin  18 volts, protecting pins
    male or female DTE/DCE ports.              340 amps
    Male/Female genders are reversible   1-25 and chassis
    with reversible thumbscrews.
    D10B2
    10Base-2 thin coax protector (BNC   7.5 volts, protecting center,
    m/f). Also protects IBM 3270 and  shield and chassis  750 amps
    CCTV lines.
    DCATV
    Coaxial protector for TVs, VCRs, pro  7.5 volts, protecting center  750 amps
    video supplied by CATV (“F” m/f).  and shield conductors
    Call Tripp Lite Customer Support at (773) 869-1234 for additional applications.
    3
    200810167  93-2858.indd   3                                     12/16/2008   9:58:51 AM

Скачать инструкцию

Файл скачали 5 раз (Последний раз: 30 Июля 2019 г., в 00:54)

Загрузить

Инструкции к похожим моделям