Скоростной кабельный маршрутизатор DOCSIS 2.0 с 5-портовым коммутатором и USB-портом ZYXEL Prestige 964 Cable Router. Инструкция на английском языке

P964 APR 964
Cable Router with 11g AP
Quick Installation Guide VER. 1.0

Rear Panel Connections
PORT                                     CONNECTION
CABLE                     Connect the F-type connector to the CATV outlet using a
coaxial cable.
POWER                     Connect the external power adaptor to the P964 APR and
plug it into an appropriate power outlet.
TO a COMPUTER                          TO a HUB
LAN1~LAN4                 Straight-through/Crossover        Straight-through/Crossover
Ethernet cable                    Ethernet cable
WLAN                      IEEE 802.11g/b                    -
USB                       USB cable                         -
Before You Start
The P964 APR is a broadband cable CPE with dual modem/router operation mode. In
order to use your P964 APR, you need to establish an internet access account with your
local cable operator.
1.  A cable Internet service that supports two-way cable modem access.
2.  A coaxial cable line which has been prepared for cable modem service by your ISP
or cable operator.
3.  The P964 APR’s Media Access Control (MAC) address is labeled on the bar code
sticker. The MAC address consists of 12 characters preceded by the text “HFC
MAC:”.
Use the HFC MAC address for registering with your cable operator.
4.  The IP address(es) of the Domain Name System server(s) is supplied by your ISP.
5.  The P964 APR is configured as a router with NAT and DHCP enabled and with
following factory default.
LAN IP Address                    192.168.1.1
Subnet Mask                       255.255.255.0
DHCP IP Pool                      192.168.1.33 – 192.168.1.64
Web username                      webadmin
Web password                      1234
Note: The default might be different from different cable operators. Please
consult with your cable Internet service provider for any change.

Preparing Your Network
1.  Your computer must have a 10M or 100M NIC (Network Interface Card), USB
interface or IEEE 802.11g/11b compatible client.
2.  If using USB connection, you have to install the USB driver. Insert the supporting
CD into the CD-ROM drive before you connect the USB port of P964 APR to the
USB port on your computer and power on your P964 APR at the first time. System
may automatically hint you the installation guide for USB driver and specify the
directory where USB driver is stored according to the step-by-step instruction after
the CD-ROM drive is ready to read. The USB driver supports Windows 98SE, ME,
2000 and XP.
TCP/IP should already be installed on computers and configure your computer as a
DHCP client.
The following procedures are for dynamic IP addresses.
Setting up Your Windows 95/98/Me Computer
Installing TCP/IP Components
1.  Click Start, Settings, Control Panel and double-click the Network icon.
2.  The Network window Configuration tab displays a list of installed components.
To install TCP/IP:
a.  In the Network window, click Add.
b.  Select Protocol and then click Add.
c.  Select Microsoft from the list of manufacturers.
d.  Select TCP/IP from the list of network protocols and then click OK.
Configuring TCP/IP
1.  In the Network window Configuration tab, select your network adapter’s TCP/IP
entry and click Properties.
2.  Click the IP Address tab. Click Obtain an IP address automatically.
3.  Click the DNS Configuration tab. Select Disable DNS.
4.  Click the Gateway tab. Highlight any installed gateways and click Remove ..
5.  Click OK to save and close the TCP/IP Properties window.
6.  Click OK to close the Network window.
7.  Turn on your P964 APR and restart your computer when prompted. Insert the
Windows CD if prompted.