Беспроводная унифицированная точка доступа с поддержкой PoE D-LINK DWL-2600AP. Инструкция на английском языке

Quick Installation Guide
802.11n Unified Access Point
This document will guide you through the
basic installation process for your new
D-Link Unified Wireless Access Point.
DWL-2600AP
POWER
LAN  2.4GHz
Documentation also available on
CD and via the D-Link Website

About This Guide                 Optional Accessories
ENGLISH  This installation guide provides basic instructions   -  PoE Base Unit (Model: DPE-101GI)
for installing the DWL-2600AP Wireless Access
Point on your network. For additional information
the package. If any of these items are required,
about how to use the Access Point, please see   Note: These accessories are not included in
the User Manual, which is available on the CD   please contact your reseller to order it.
included in this package or from the D-Link
support website.
Hardware Overview
System Requirements
LEDs
-  CD-ROM Drive
-  Windows , Macintosh , or Linux-based
®
®
operating system
-  Ethernet port or installed Ethernet adapter   POWER  LAN  2.4GHz
-  Internet Explorer 7.0, Safari 5.0, Firefox 4.0,
or higher
Figure 1. DWL-2600AP LEDs
Unpacking the Product             2.4 GHz –  When this LED is lit up, the access
point’s 2.4 GHz radio is enabled. It will
Open the shipping carton and carefully unpack its   blink when there is wireless traffic.
contents. Please consult the packing list located          LAN –  When this LED is lit up, the device’s
in following information to make sure all items are   Ethernet port is connected to an active
present and undamaged. If any item is missing   router or switch. The light will blink
or damaged, please contact your local D-Link   when there is traffic going through
reseller for replacement.               the port.
POWER –  When the LED is lit up, the access
- DWL-2600AP 802.11n Unified Access Point  point is powered and ready for use.
- Power Adapter
- Mounting Ring                Interfaces
- Ethernet Cable
- Console Cable*
- CD-ROM
- Ceiling Bracket (3 sets, sizes are 9/16", 14/16",
and 1 1/2")
Note: Using a power supply with a different
voltage than the one included with the
DWL-2600AP may cause damage and will void
the warranty for this product.
*The console cable is an optional accessory and
not included in the package in Armenia, Azerbaijan,
Belarus, Georgia, Israel, Kaliningrad, Kazakhstan,
Kyrgyzstan, Latvia, Lithuania, Moldova, Mongolia,   Console Port  Power Receptor
Russia, Turkey, Turkmenistan, Ukraine, and   LAN Port (PoE)
Uzbekistan. If a cable is required, please contact
your reseller to order it (Model: ACS-AP-CONSOLE).  Figure 2. DWL-2600AP Rear Panel
2  ?  D-Link DWL-2600AP Quick Install Guide

•   Manage the access point from the computer
via the Unified Wireless Switch or Wireless
Controller: Connect the access point to   ENGLISH
a Unified Wireless Switch or Wireless
Controller. Connect your computer to the
same network as that of the Unified Wireless
Switch or Wireless Controller.
Power Button      Reset Button   DWL-2600AP DWL-2600AP  Computer  Computer
Unified Wireless Switch
(For Power Adapter)                             or
Wireless Controller
Installation                     Mounting Options
Power on the access point        You can mount a DWL-2600AP access point on any
of the following types of surfaces:
To power on the DWL-2600AP, you can use ONE of
the following methods:           • Solid surface wall or ceiling
• Tabletop
1. Connect the supplied power adapter
OR                           Cable Requirement
2. Plug one end of an Ethernet cable into the LAN   Use a CAT 5 cable with an even sheath.
port of the DWL-2600AP and the other end into   The Ethernet ports on the DWL-2600AP access
a port on a PoE switch.         point cannot accept a CAT 5 cable that has an
uneven sheath; the RJ-45 connector on the cable
will not fit properly into the receptacle on the access
point.
Configure the access point
Wall Installation Recommendations
To set up and manage the DWL-2600AP, use one   If you plan to install the DWL-2600AP on a wall or
of the following methods:        other vertical surfaces, orient the top of the access
point (the side with the LEDs) toward the intended
•   Manage the access point from the computer:   coverage area. The radio antennas transmit through
Connect the access point and your computer   the top of the access point but not through the
directly via a straight-through Ethernet cable.   bottom (where the bracket is).
Warning: The DWL-2600AP is designed to
receive PoE power only from an 802.3af-compliant
source, or from a D-Link-approved power injector.
Connecting an access point to a Power over
DWL-2600AP     Computer
Ethernet (PoE) device that is not approved by
D-Link can damage the equipment.
•   Manage the access point from the computer
via the Switch or Router: Connect the
access point and your computer to the same
switch or router.
Switch or Router
DWL-2600AP  DWL-2600AP  Computer  Computer
D-Link DWL-2600AP Quick Install Guide  ?  3