CD-ROM SAMSUNG SC-140B. Инструкция на английском языке

SC-140/148
CD-ROM DRIVE
User's Guide - ENGLISH
http://www.samsungelectronics.com
moisture.
CAUTION
WARRANTY
CD-ROM drive.
Safety Warnings
1
local SAMSUNG representative for all repairs.
Please refer to the Samsung limited warranty statements.
You must not use the drive in any manner other than that specified in this guide.
those specified here in may result in hazardous radiation exposure
The following diagrams illustrate the precautions to be taken when using your
To reduce the risk of fire or electric shock, do not expose this appliance to rain or
Do not attempt to repair the CD-ROM drive yourself. Contact your dealer or
Use of controls or adjustments or performance of procedures other than

4
5
6
1
2
3
1
LED
button.
Disc Tray
2
remain closed.
Emergency Hole
hole to eject the disc.
Open/Close-Button
Volume Control Dial
Headphone Connector
3
COMPACT
2
drive. It requires a 3.6 mm stereo mini-jack.
4
If the disc tray does not open when you press the Open/Close
Front View of the CD-ROM Drive
56
utilities. For example, the Microsoft Windows Media player can be used.
When in play, press the stop key and when in stop, press open/close key.
This control dial adjusts the volume for your headphones. You can only use the
u When you place a disc in the tray, make sure that the label on the disc is
button, insert a small  metal rod(an unwound paper clip for example) into this
headphone jack and volume control when you have installed the required software
*This function should only be performed when the computer is powered OFF.
The Disc Tray opens and closes automatically when you press the Open/Close
The audio output connector enables you to plug stereo headphones into the
facing upwards. If you are not loading or unloading a disc, the disc tray should
1
2
5
3
4
1
Digital Audio
23
Power Connector
Audio Output Connector
supplied with your sound card.
Device Configuration Jumper
Host IDE Interface connector
S
C
L
and place it in the correct position.
S
4
3
A
M
your drive using this two-pin connector.
from the IDE interface to the CD-ROM drive.
The power connector is a four-conductor male plug.
Usually, this is a pre-set configuration as illustrated below.
Rear View of the CD-ROM Drive
5
You can connect a sound card to your drive using this four-pin connector.
This input/output interface connector is used to connect the 40-pin flat cable
You can connect a sound card or MPEG card which support Digital Audio to
* Verify that the setting is as illustrated. If it is not, simply remove the jumper
* This function is not covered in detail in this guide. Refer to the documentation

3
1
2
4
5
6
Item
*
Disk space
drive.
MS-DOS version
Windows version
button is on the right.
Type of computer
Free expansion unit
do not seem to fit.
held firmly in place.
Put the cover back on your PC.
cables Iocated inside your computer.
4
To install the drive, proceed as follows.
System Requirements
which the CD-ROM drive is to be installed.
u If you use screws that are longer than the
Turn OFF your computer. Remember to verify the
5.25 inch
mounting screws. (recommended standard M3x6x4)
recommended standard, you may damage the
Description
Remove the blank cover panel of the 5.25 inch unit in
* u Depending on your PC model, you may need to
Installing the CD-ROM Drive
configuration jumper on the rear of the CD-ROM drive.
attach guide rails to the drive, so that the drive is
3.1(or higher)
5.0(or higher)
that your set-up meets the system requirements listed below.
Install the CD-ROM drive into the unit and secure it with
Remove the cover of your PC. (main unit of the computer)
* Connectors are keyed so it is impossible to put them in
100KB minimum
Connect the CD-ROM drive to the IDE interface and power
an incorrect position. Do not force the connectors, if they
compatible computer)
an IDE interface(or a 100% IBM-
IBM 486SX 20MHz (or higher) with
Install the CD-ROM drive in your computer horizontally, making sure that the Open/Close
Before you install the CD-ROM drive, we strongly recommend that you make certain
6
4
7
5
3
2
1
?
To...
Result :
Result :
DOS user
DOS user
If you are a...
If you are a...
Windows user
Windows user
Windows 95/98 user
Reboot your system.
Exit without installing
floppy disk from the drive.
Confirm the installation
When the Setup Completed
u
u
Run the CDSETUP program:
5
Then :
Then :
u The computer restarts
Type a:
Installing the Software
File Manager
u Click on the A
u Click on the A
Turn on your computer and wait for it to boot.
u Press RETURN
u Type CDSETUP
You can install the device driver for DOS or for Windows.
icon.
icon.
(Remark CD-ROM Driver in the state of CONFIG. SYS.)
Y
N
Press the RETURN key
u Access the File Manager
u Click on MY COMPUTER
Double-click CDSETUP.EXE
at the DOS prompt
u Both the device driver and MSCDEX are loaded
u necessary to install Device Driver.
icon.
u Creates a SAMSUNG directory on your hard disk
Insert the driver disk into a floppy disk drive(usually the A drive).
Then enter...
u Modifies the CONFIG.SYS and AUTOEXEC.BAT files
Do not install DOS Driver when the program of Windows 95/98 is going on.
after the A: prompt
u Windows 95/98, then install as follows.
u Whereas, when you are in Dos Mode of
If you answer Y(Yes), the installation program automatically
screen is displayed, remove the installation
u When you are in Windows 95/98, it is not
from the Windows
u Copies the required softwares (mscdex.exe and sscdrom.sys)